The main causes of formation are: low melting temperature, poor melting, excessive mirabilite particles in the compound, insufficient addition of coal powder, and contact between the glass liquid and refractory materials, etc.
Solution method

1. Melting and clarifying bubbles: These are bubbles caused by unstable raw materials, melting, fuel, and combustion systems;
2. Non-melting clear bubbles: These are bubbles caused by the quality of the brick material, nitrate condensates and cooling equipment
(1) The air brought in by the raw material foaming compound forms bubbles - air carried in by raw material lumps (sheets) or ultrafine powder lumps (sheets), large mirabilite particles, and broken glass. Carbon dioxide - the decomposition product of carbonates when the compound melts; Water vapor - Water added to the compound materials; Nitrogen - air is carried into the compound and added to the melting furnace. Oxygen has a relatively high solubility in the glass liquid, and most of the remaining gas is nitrogen. Gases are divided into soluble and insoluble gases. Insoluble gases include nitrogen, carbon dioxide and argon. The soluble gases include oxygen, sulfur dioxide and water.

(2) The liquid level line around the melting furnace outside the bubble boundary: Small bubbles come from the high-temperature area of the melting furnace; Because the process by which bubbles are absorbed or dissolved by glass is related to time, the higher the temperature of the glass, the more gas is absorbed by the glass, making the bubbles smaller. Bubbles with a diameter of less than 0.2mm usually come from the melting part. Bubbles with a diameter of 0.5mm usually occur at the neck-sticking area. Larger bubbles come from the cooling section or the flow channel. The reason is that there is a glass phase of refractory material precipitated around the glass liquid level line, which has remained around the refractory material at the liquid level line for a long time. The outside of this part is the cooling air from the pool wall. The cooling air makes the inner side of the brick joints on the pool wall even colder, which is conducive to the accumulation of mirabilite. Under the changes of temperature, furnace pressure and liquid level, the accumulated mirabilite enters the glass liquid, generating bubbles. The heavy-duty insulation of the pool wall and the gaps between the pool wall bricks cause the glass liquid to seep out and enter the insulation layer of the pool wall, resulting in gas flowing into the glass liquid in the kiln along the gaps of the pool wall and generating bubbles. Solution: Stabilize the pressure of the melting furnace, stabilize the convection of the glass liquid, block the gaps in the pool wall, and stabilize the flame of the small furnace.
(3) Clarified microbubbles generally refer to bubbles with a diameter of less than 0.2mm. Microbubbles mainly occur in the clarification section. Reason: The clarification temperature is too low, and the flame of the small furnace is either too strong or too weak. The flame atmosphere in the clarification zone has poor reducing properties, the fuel atomization is poor, the oil contains a large amount of particulate carbon, the bubble boundary is unstable, and the flame is unstable. The sudden change of convection. In addition to the influence of clarification temperature, it is also affected by unstable bubble boundaries, significant changes in the speed of the feeding machine, large variations in liquid level height, and significant changes in the atmosphere inside the melting furnace. The fuel oil contains granular carbon, which is scattered on the surface of the glass liquid, resulting in poor atomization of the oil. Sudden changes in the amount of melting can also cause clarification bubbles.
(4) Causes of necking bubbles: The bubbles produced by the necking cooling equipment and the partition hanging wall. Here, the cooling equipment includes two types: large water pipes and agitators. Water leakage in the cooling equipment can cause bubbles. The cool glass liquid at the stirrer contains fallen mirabilite. The mirabilite condensed in the exposed space of the large water pipe drops into the glass liquid due to the change in pressure in the cooling section, causing bubbles. This kind of bubble is usually located in the upper, middle or lower part of the glass plate and has no obvious pattern. Observed under a microscope, there are usually traces of mirabilite of varying degrees of severity. Bubbles will be produced when the crystallized glass is redissolved. Solution :① Check whether the cooling equipment is leaking. ② Check whether there are any traces of mirabilite or foreign objects around the liquid level line of the cooling equipment. ③ Strictly control the pressure in the cooling section, which is generally maintained at 8 to 15Pa. ④ In the design, reduce the exposed space of large water pipes. The exposed parts of the large water pipes should be covered with glass liquid. ⑥ Stabilize the glass liquid level. ⑦ Stabilize the pressure of the cooling water.
(5) Reasons for the bubbles in the cooling section: One is the bubbles generated in the upper space and the liquid level line, and the other is the bubbles produced at the bottom. Bubbles produced in the upper space and at the liquid level line usually exist on the upper surface of the glass and are in a closed state. Bubbles caused by mirabilite falling from the upper space, when observed under a microscope, usually contain mirabilite traces of varying degrees of severity. Bubbles produced near the liquid level line are usually caused by the quality of the bricks, the gaps between the bricks on the pool wall, or foreign objects adhering to the pool wall. The bubbles produced at the bottom of the cooling pool are generally caused by the quality of the brick material, foreign objects, and residual welding slag and ironware from the installation stage. Their diameters are usually between 0.5 and 1.0mm or larger. Solution: For the bubbles generated in the upper space and the liquid level line: ① Stabilize the pressure in the cooling section. ② Keep the cooling air pure. ③ Separate the melting section from the cooling section as much as possible to reduce the pollution of the exhaust gas from the melting section to the cooling section. ④ Reduce the impact of the external environment on the cooling section. ⑤ Check whether there are any foreign objects at the liquid level line on the pool wall. For the bubbles produced at the bottom of the cooling section pool :① Check the glass liquid level in the cooling section to see if there are any bubbles discharged from the bottom. ② Remove the insulation at the bottom of the cooling section to lower the temperature at the bottom of the cooling section pool. ③ A cooling fan can be used to cool the bottom of the pool, but it is necessary to pay attention to preventing crystallization. ④ Increase the iron content in the glass composition and reduce the heat permeability of the glass. ⑤ Try to increase the size of the large water pipe as much as possible to reduce the backflow of the glass liquid.
(6) Channel Bubbles: Channel bubbles are divided into two types. One is generated from the bottom of the channel, and the other is caused by the drop of mirabilite in the upper space of the channel or by the channel gate plate. Bubbles generated from the bottom of the flow channel: Generally, they are on the lower surface of the glass plate. The bubbles are closed, and even if they are open, there are traces of rupture at their edges. The diameter is generally between 0.5 and 1.0mm. Sometimes, the diameter of the bubble varies depending on the cause. Reason :① The bottom brick contains a relatively large amount of metallic iron, which is concentrated. ② The brick joints are relatively large, causing the glass liquid to leak. ③ The scattered welding slag during installation was not cleaned up thoroughly. ④ Metal or brick-like materials are bonded to the surface of the base brick. Solution :① Reduce the temperature of the flow channel. ② Remove foreign objects. The mirabilite falling from the upper space of the flow channel or the bubbles produced by the flow channel gate plate: The bubbles produced by the mirabilite falling from the upper space are usually accompanied by impurities existing on the upper surface of the glass, presenting as strips on the upper surface of the glass plate and generally disappearing within a short period of time. The flow channel gate plate bubbles are generally present on the upper surface of the glass, in a dotted and linear pattern, and are regularly spaced. It is generally caused by cracking at the lower edge of the gate plate. Solution :① Reduce the temperature of the flow channel. ② Stabilize the pressure of the cooling section and keep it below the pressure of the tin bath. ③ Increase the amount of protective gas used for the zero shell in the tin bath. ④ Seal the gaps of the flow channel. ⑤ Replace the flow channel gate plate. ⑥ Strictly control the SO3 in the glass composition.
(7) The bubbles formed on the bottom bricks of the tin bath usually occur in the high-temperature zone of the tin bath in the newly put into operation float line. The location where the bubbles are formed can be observed through the tin bath observation window. The bubbles in the original glass plate have openings on the lower surface. The openings are large, the depth is shallow, and the macroscopic deformation is obvious. Reason :① The bricks at the bottom of the trench are damp and have a high moisture content. ② The porosity of the bricks at the bottom of the groove is relatively high. During the heating stage of the tin bath kiln, the moisture in the bottom bricks was not completely drained. ④ Gas discharge from the brick joints or bolt holes of the bottom bricks. During installation, the residual metal dissolves with tin to produce gas. Solution: Drill a 10mm diameter hole on the bottom shell steel plate at the position where the bubble at the bottom of the groove is formed. Generally, it is necessary to drill a 30mm depth into the bottom brick and use a conical wire. It is led out with a copper tube and connected to the vacuum pump. The number of holes depends on the number of bubble sources.
